Product
Bale sizes of
30 x 50 , 40 x 60 , 60 x 80 , 60 x 100 , 70 x 100 cm.
Bales both ferrous and non-ferrous Excess scrap is trimmed thanks to the shearing lid.
PRODUCT CATALOGUE DATA SHEET
 - DURABLE
Thanks to their heavy construction Birim Makina balers are extremely durable. The proof is the hight demand from the market for brand new and second hand products.   
 - HIGH QUALITY CYLINDER
 Birim Makina balers are manufactured using high quality cylinders. Rods are hardened and chrome coated while the pipes are honed. Technical knowledge derived from years of experience keeps our cylinders in operation for long years.   
 - RESISTANT to WEAR
All surfaces that are in contact with scrap (Charging-box, rams, lids) are covered with Hardox type wear resistant liner plates. The wear plates are connected to the press box by countersunk screws. This helps to replace the plates easily and quickly after normal wear.  
 - GUIDES
On the press box bottom and sides guides are installed for smooth operation and to reduce jamming. The guides are installed with screws and can be replaced easily and quickly after wear.
 - FAST OPERATION
 Multiple pump application provides fast cylinder movements. High tech hydraulic applications supplies faster cycles with the same motor power.   
 - LOW ENERGY CONSUMPTION
Another advantage of the multiple pump application is the lower energy consumption. The system is designed to run at high efficiency therefore the consumption is less.    
 - AUTOMATIC OPERATION
A Siemens PLC controlled automatic operation increases the capacity of the machine. A control panel is supplied with joysticks for manual operation when required.
 - RADIO CONTROL
A variety of remote control devices are supplied according to the customers’ individual requirements. Automatic and manual operations can be controlled from the remote control. A range of 100 meters is possible in most cases.  
 - ELECTRIC SYSTEM
The latest Siemens and Telemecanique components are used in the electrical system.  
 - HYDRAULIC SYSTEM
Equipment is choosen from world known high quality brands according to application and power requirement. Our hydraulic system is designed in our R&D department and installed by our experienced staff. Hydraulic manifolds are also manufactured in our company under stringent quality control.
Whenever possible pipes are bent in favour of welding. Pipe-work is therefore resistant against shocks. The inner surface of the pipe-work is treated with special chemicals before assembly to prevent contamination of the pipes.
 
 - NON CONTACT SENSORS
 Automatic balers have non-contact inductive sensors. The inductive sensors operate away from the moving part hence there is no contact with the sensors. The closed sensors are installed inside the rod of the cylinder. They provide very precise data to the PLC. All these non-contact sensors prolong the re-setting period and operational life. Research shows that Shears are mostly interrupted by sensor problems, the non-contact sensors eliminates most of these interruptions.  
 - FILTER SYSTEM
Baler is equipped with high quality air, return, circulation and suction filters. These filters keep the oil clean and protect the hydraulic equipment and oil quality. Air filters stop particles from outside contaminating the tank. Upon request special humidity stopper filters can also be installed. Return filters filter the oil coming back to the tank, whilst suction filters filter before the pumps and protect them from the dirt. Circulation filters continuously filter the oil in the tank and helps keep the oil clean. Filtration is done at 5 microns.  
 - DIRT DEDECTORS
Dirt detectors installed on some filters to signal the changing time. Therefore oil is filtrated with clean filters so remaining clean for a longer time.  
 - REMOTE DIAGNOSIS SYSTEM
In case of a breakdown, our service department can connect to the baler via a built in modem to diagnose the problem promptly.  
 - DIGITAL DISPLAY
A long lasting process display is installed in some machines. Basic parameters such as pressure, oil temperature, etc are shown on the panel. Basic settings can also be done easily with the help of the display.  
 - LONG LASTING BLADES
Blades on the chamber and lids are made of high quality tool grade steel. Blades are hardened, precisely machined and 4 sides can be used.  
 - COOLER
Cools and protects the oil and the hydraulic parts.  
 - SPARE PARTS
A high number of parts from manufacturers including Rexroth, Siemens, Telemecanique, are available from our stock in case of a sudden breakdown or routine maintenance.  
 - SERVICE
Well trained, experienced, efficient personnel service our machines. We also cooperate with local service centers around the world.